When you are using a table saw, you are already dealing with a lot of unsafe operations. But you can never use a saw without a blade guard. The Ridgid table saw guard can keep the Ridgid saw safe and you safer.
If you own one from this brand, you don’t need to worry about how to install blade guard on Ridgid table saw anymore. We will show you easy paths to do this!
Have a look at our easy method!
Method of Installing Ridgid Table Saw Blade Guard
If you have a Ridgid table saw guard, you can go through this easy process for installing the blade guard. Check it out and do it yourself!
Step 1: Unscrew the Wing Nut
source: youtube.com
First of all, you have to keep the saw blade teeth down towards the front part of the saw. After doing this, you will need to unplug the saw.
In this case, keep in mind that if the blade teeth are not pointed towards the front of the saw, the blade or the saw might get damaged.
Now, once you unplug the saw, you have to remove the blade wrenches first from the storage area. For this, search for the wing nut and once you find it, unscrew it carefully.
Step 2: Rising the Blade
Now that you have unscrewed the wing nut, you have taken the saw blade lower and then carefully, take out the throat plate.
While doing this, you must check the bevel locking lever. It must be securely pushed to the left side to provide you the safe passage. Once you are done with this, you have to get your hands on the saw blade and raise it upward. If you have a Lightest gas powered pole saw, you can now install the guard without any help.
Take it to its full height. Adjust the height adjusting knob to the highest. For this, you have to move the knob clockwise. When you have already done it, check the riving knife and position it to the UP option.
Step 3: Lifting the Guard Lever
source: youtube.com
Once you are done with installing the saw blade, you can easily install the blade guard on your Ridgid Table saw.
After unplugging the saw, you have to raise the saw blade first. Make sure you are keeping the riving knife on the UP position here.
Don’t forget to reinstall the plate in this situation. Now, take the guard lever up so that you can install the blade guard. After lifting the guard lever, it will get unlocked for you.
Step 4: Installing Anti-Kickback Pawls
In this situation, you might want to go through the install the anti-kickback pawl before you try the blade guard.
For this, you have to press the button situated on the right side of the anti-kickback pawls. Hold the button for a while.
After this, you have to align the slot into the pawls. Get them over the rear hole in the riving knife. With your hands, keep pushing the pawls down.
Snap the pawls into the right place first. Now, you are free to release the button you were holding.
To certify the locked pawls, you have to pull the handle and recheck it. However, keep in mind that the anti-kickback pawls will only be necessary for the through cuts. Otherwise, you will not need them.
Step 5: Aligning the Blade
source: ourhomesmagazine.com
In this situation, you will see that the front part of the blade guard is raised already. As it is open, now, you have to get your hands on the back of the guard.
Hold it and lower the back part slowly. Lower it into the middle hole of the riving knife. After this, start pushing the front part of the guard.
Push it down so that you can get it to its right level. Keep pushing the front part and make it parallel to the table.
This step is necessary because if the blade guard is not parallel to your table, the riving knife will not be in the UP position. Make sure you keep the two lines parallel.
Step 6: Locking the Guard
You are almost done with the blade guard installation process for the Ridgid table saw. In this position, you have to lock the guard in its place.
For this, use your hands to push the guard lever down. When you are done, you must know that the installation process is completed.
Step 7: Things to Remember
source: bolis.com
When you are settling for the blade alignment, you cannot rely on one alignment. It depends on the blade widths. This alignment will be different for different blade width.
Also, keep in mind that you should never operate the Ridgid table saw without installing the blade guard. The blade guard is added to the machine for your safety.
It is highly recommended that if you do not know how to install the blade guard properly, take it to a professional before using it.
Don’t install or hold the blade or saw without the proper safety measures. Get gloves, glasses, and cover yourself up for going through the steps.
Final Verdict
So, you have already learned how to install blade guard on Ridgid table saw. We have mentioned the whole process in an easier method.
Try out the process at home and let us know how you did it. Is there any other process of installing it? Let us know in the comment box!
